Why is the Stanley 5.5hp 2900PSI Petrol Pressure Washer so good?
When purchasing a pressure washer for domestic use. Determining the best pressure washer for home use (Australia) can be quite daunting. This article is about the Stanley 5.5hp 2900PSI Petrol Pressure Washer which is a domestic grade pressure washer with commercial quality and features.
Selecting the Optimal Pressure Washer
When in search of the most suitable power washer to address your cleaning requirements, it is imperative to consider the unit’s power capacity, as it directly influences its versatility. The pivotal factors in evaluating this power lie in pressure output, denoted in pounds per square inch (PSI), and water volume, quantified in gallons per minute (GPM). By scrutinizing these PSI and GPM specifications, one can gauge the cleaning prowess of a pressure washer. A unit boasting higher PSI and GPM ratings exhibits superior efficiency and expediency in cleaning tasks, albeit at a premium cost compared to its lower-rated counterparts.
Typical flow rates for medium-duty:
pressure washers range between 1 and 3 GPM, with pressures ranging between 1900 and 2788 PSI. These sturdier, more powerful devices are ideal for home or in the shop. They make it simple to clean everything from exterior panelling and fences to patios and decks.
Heavy Duty and Commercial:
Heavy-duty pressure washers have a starting pressure of 2800 PSI and a maximum flow rate of 2 GPM or more. Pressure washers designed for commercial use start at 3100 PSI and can provide up to 4 GPM at high pressure. Various large-scale cleaning activities, such as cleaning decks and driveways, washing two-story homes, removing graffiti, and stripping paint. Are all made simple by these rugged machines?
The Stanley 13.5HP Petrol Pressure Washer (4200PSI) is great for cleaning your concrete driveway. And furthermore, paved areas, car, motorcycle, truck, walls, or garden features. It has a 13.5 horsepower motor and produces 4200 PSI of pressure.
The Briggs and Stratton 4 Stroke engine provides the highest performance. Thus, value for your pressure washer at a reasonable price. It comes with a convenient 20-foot heavy-duty hose, five interchangeable nozzles. And two 800-millilitre detergent bottles that may be used with each bottle’s same or different detergents. This pressure washer is ideal for any tradesperson or handyperson who wants to make cleaning the outdoors more straightforward and faster than ever before.
Preparation for the Pre-Operational Phase
If the device has been previously used. The motor, muffler, and exhaust may still be hot enough to cause a fire. When inspecting the pressure washer, proceed with safety at all times. Check to see that the fuel/engine switch is not turned on.
Ensure that the spark plug lead is securely secured to the top of the spark plug before continuing. Holding the cage, rock the pressure washer while listening for any noise. Which could indicate a loose item in the machine. If something appears to be loose, either tighten it or consult with a service agent to determine what is wrong.
Refueling the Fuel Tank with UNLEADED 91 PETROL (ETHANOL-FREE)
It is paramount to consistently employ clean and fresh fuel when refueling your pressure washer. The utilization of stale fuel carries the risk of causing operational irregularities, potentially leading to engine damage. Please be advised that such damage falls outside the scope of warranty coverage.
Before refueling, ensure that the engine is completely turned off. Verify that both the gasoline tap and engine switch are in the off position. Confirm the secure fitting of the fuel tank cap; overfilling the tank above the fuel filter’s level is strongly discouraged.
Introducing Lubricating Oil to the System
When incorporating lubricating oil, adhere to the use of automobile engine oil, specifically SAE 30W or SAE 15W-40 4 Stroke Motor Oil. Always prioritize the use of pristine and current oil supplies to maintain optimal performance. The utilization of incorrect or outdated oil may result in undesirable engine behavior, ultimately voiding the manufacturer’s warranty.
When replenishing the oil reservoir, ensure that the engine is turned off, and take caution to maintain a level position. It is of utmost importance not to tilt the unit or employ a funnel during the oil-filling process. Add oil only until it reaches the top of the threaded section. Prior to initiating the pressure washer, double-check the secure placement of the oil filling cap.
A note of caution: Overfilling the oil may lead to potential damage to the pressure washer, thereby nullifying warranty coverage.
Bottles and Tubes of Detergent
Connect the detergent tube to the nipple by pushing the tube into the nipple. This model pressure washer comes with two 800ml detergent bottles. Which can be used with the same or different detergents depending on your preference. Fill the detergent bottle or bottles with water, and then turn the selector to the bottle you want to utilise.
Reminder: The detergent will only flow when the low-pressure black nozzle is used in conjunction with a slowing of the motor speed.
Nozzle colour selection & their meaning
Black
This nozzle is for low-pressure applications and should be used in conjunction with a detergent tube and filter. The engine speed must be set to a low setting.
Red 0 Degrees
This nozzle is designed for high pressure and produces a single stream of water that looks like a pencil.
15 Degrees yellow in colour
This nozzle is designed for high pressure and produces a 15 Degrees “fan” of water spread across a wide area.
25 Degrees in the shade of green
This nozzle is designed for high pressure and produces a 25 Degrees “fan” of water spread across a wide area.
White 40 Degrees
This nozzle is designed for high-pressure applications and produces the broadest 40 Degrees “fan” of water available.
Nozzles are connected and disconnected.
Connect
Pull the QC collar down, Insert the nozzle into the hole. Then, release the QC collar, and then click the nozzle into place.
Note: If the nozzle is still loose or leaking, check the o-ring at the other end of the lance. If replacement is required, refer to the “Troubleshooting” section.
Pull the QC collar down, lift the nozzle out, and then release the QC collar.
Get started with your pressure washer.
Check the amount of the oil; Fuel should be checked and refilled. Connect the garden hose to the cold water supply; do not turn on the water!
Connections: Connect the garden hose to the garden connection on the pump; Choose a nozzle (as shown above); By sliding the choke lever to the LEFT, you may turn the choke on and off. By sliding the gasoline lever to the right, the vehicle will be ready to run. Change the setting of the switch to “1”; After you have engaged the recoil starter, pull it briskly until it stops working. This procedure may need to be done several times before the pressure washer engine fires up; this could take up to 12 pulls.
Never draw the recoil after the engine has started since it could damage the engine. Any damage that occurs as a result of this will not be covered under warranty.
Once the game has begun, turn the choke to off (run) and slide to the RIGHT. Turn on the cold water supply. Release the safety lock on the trigger by pressing the lever down. Squeeze the wand’s trigger to activate it. Maintain pressure until all air has been expelled and a steady stream of water is flowing through; To halt the flow of water, pull the trigger.
When you’re done with the detergent.
Release the trigger on the wand when you are through with the detergent. Remove the filter and tube from the detergent bottle. The tube and filter should be wrapped around the handle. Do not place the pump on the ground, as this will cause dirt to be sucked into the pump. Damage occurring, as a result, will not be covered under warranty. Changing the nozzle and pressing the trigger will allow you to continue cleaning with clean, cold water.
Taking a pause during the course of the use
If you need to take a break from using the pressure cleaner for more than 2 minutes, you must switch it off. Please see page 15 for instructions on how to achieve this. If the pressure washer is kept running for more than 2 minutes with the trigger depressed. Where no water is flowing out, it will cause damage. Damages resulting from the accident will not be covered by the warranty. The pressure washer pump may also “dump” hot water as a self-preservation measure. If the pump’s temperature becomes too high during this period.
Cleaning of the Nozzle
It is possible that clogging of the spray tip will cause an increase in water pressure. Which could damage the pump unit. Spray tip deposits can be removed by carefully inserting the included spray tip cleaner. Or a thin, sharp instrument (such as a paper clip) into the tip and wipe away the buildup.
Please keep in mind that a clogged nozzle is most likely the reason for the motor’s labour. As previously stated, clean the nozzle.
Fuel Tank and Carby drainage
Starting the engine will be difficult when residual fuel has been left in the engine for an extended period. Turn on the fuel valve to ensure that all fuel has been drained and the tank is completely empty. Position a fuel container suitable for use under the carburettor drain screw to catch any spilt fuel; remove the bolt.
Allow the fuel to completely drain into the container. The drain bolt should be tightened. Draining the fuel tank and carburettor is followed by starting the engine and allowing fuel to be totally consumed. For information on properly disposing of fuel, consult your area’s hazardous waste management rules.
Cleaning your pressure washer
NEVER attempt to clean the pressure washer using the pressure washer itself. Damage caused by cleaning the pressure washer with the gun that came with it will not be covered under warranty. Ensure the pressure washer is entirely cooled before cleaning, which should take about 1 hour after usage. All surfaces should be cleaned with a gentle, clean cloth.
All of the nozzles should be rinsed in a pail of clean water. Place in a drying holder until dry. Check that the petrol tap is turned off. Ensure that the engine switch is turned off. So to avoid kinking the high-pressure hose, it should be left wrapped up. Keep cool and dry so that it won’t get frozen. Storage should be done in a safe area away from children and the elderly.
Storing for extended periods
The engine is started and runs for no longer than 30 seconds. If you are storing your pump or motor for less than 4 weeks. Please follow these guidelines to guarantee that no harm occurs to the pump or motor. Any damage that occurs as a result of this will not be covered under warranty.
This removes any extra water from the pump.
Check to see that the inlet water hose is not attached. And It is essential to ensure that the high-pressure hose is not connected to the pump. Turn on the gasoline faucet. Turn the choke lever to the on position (start). Ascertain that the high-speed lever is engaged. Turn the switch to the “on” position. Pull the recoil lever; turn the choke to the off position (run); Allow no more than 30 seconds for the motor to run. Slow down by sliding the speed lever. Turn off the fuel faucet. Turn off the engine by pressing the button on the ignition switch. Remove the petrol from the tank and carburettor; Clean per “cleaning”. If the pressure washer is not used or stored for more than one month. The following storage practice should be followed.
Drain the carby
Disconnect the fuel supply lines to both the fuel tank and the carburettor. Then double-check that all of the fuel has been drained. Remove the spark plug and fill the spark plug hole with roughly one tablespoon of clean engine oil. Replace the spark plug.
Pulling the recoil starting cord numerous times while the ignition is turned off is a gentle technique. Afterwards, reinstall the spark plug and draw the recoil starting cord. Until you feel resistance from the piston on the compression stroke (this is when you should stop pulling). Under a cover, keep the pressure washer stored in a dry, well-ventilated area. To prevent dust and debris from building on the machine.
Instructions on how to use and clean with the pressure cleaner
Using or not using a detergent for deck cleaning is up to you.
Freshwater should be used to pre-rinse the deck and surrounding area. In the case of a deck wash, place the detergent suction tube straight into the cleaning solution. And apply low pressure to the surface to be cleaned. For optimal results, keep your work area to tiny areas of around 2m2. Allowing the deck wash to remain on the surface for 1-3 minutes after you finish. A patio cleaner head can be used to remove tough dirt and stains (not supplied).
Allowing the detergent to dry on the surface is not recommended. Rinsing at high pressure in a long sweeping motion. While keeping the spray nozzle roughly 75mm to 150mm away from the cleaning surface. Ensure that you are cleaning from top to bottom and left to right. When moving on to a new portion of the cleaning surface. Make sure to overlap the previous section to eliminate stop marks and achieve a more equal cleaning outcome.
Cleaning the siding of your home, with or without detergent
Freshwater should be used to pre-rinse the cleaning surface. If you’re using home wash, place the detergent suction tube directly into the cleaning solution. Then apply it to the surface at low pressure to get the most outstanding results. Limit your work area to sections approximately 2m wide, and always apply detergent from bottom to top).
Allow 1-3 minutes for the house wash to remain on the surface. Allowing detergent to dry on the surface is not recommended; simply wet it down with fresh water if the surface looks to be drying. If necessary, a special cyclone nozzle attachment (not included) can be used to remove obstinate dirt and debris. Rinse top to bottom in an even sweeping motion. While maintaining the spray nozzle roughly 150mm away from the cleaning area to avoid streaking the surface.
Patios made of cement, brick, and stone – with or without detergent
Using freshwater, pre-rinse the cleaning surface. If you’re using an all-purpose cleaner, place the detergent suction tube directly into the cleaning solution. And apply it to the surface with low pressure. To achieve the most outstanding results, keep your working area too small, roughly 2m2. Allow 1-3 minutes for the all-purpose cleaner to sit on the surface. Allowing the detergent to dry on the surface is not recommended. Apply high pressure to the cleaning surface sweepingly. Maintaining the spray nozzle roughly 75mm to 150mm away from the cleaning surface. Ensure that you were cleaning from top to bottom and left to right. Using a dirt blaster nozzle, you may get rid of even the most persistent stains.
Cars, boats, and motorcycles can all be washed with or without soap.
Freshwater should be used to pre-rinse the car. Place the detergent suction tube directly into the cleaning solution. Then apply it to the surface at low pressure if you are using a vehicle wash. If you want the most outstanding results. Clean one side of your vehicle at a time applying detergent from bottom to top. Never allow the soap to dry on the vehicle’s surface. Washing at high pressure in a sweeping motion. While keeping the spray nozzle roughly 150mm to 200mm away from the cleaning surface. The distance should be increased when rinsing pin-striping or other sensitive surfaces) is recommended.
Ensure that you are clean from top to bottom and left to right. To achieve the most excellent results, wipe the surface dry with a chamois or a soft dry towel after cleaning.
With or without detergent, BBQ grills, outdoor power equipment, and gardening tools are all OK.
Freshwater should be used to pre-rinse the surface. Place the detergent suction tube straight into the cleaning solution and apply the detergent. At a low pressure if you are using an all-purpose cleaner or a degreaser. Allow 1-3 minutes for the detergent to sit on the surface. Avoid allowing the detergent to dry on the surface. Spray the cleaning surface with high pressure while keeping the spray nozzle roughly 75mm to 150mm away.
To effectively remove highly resistant dirt, it may be essential to position the spray nozzle even closer to the surface. To increase the amount of dirt cutting action. You may wish to use a lower degree nozzle to remove caked-on muck off garbage cans. Also, lawnmower blades, wheelbarrows, and other non-sensitive metal surfaces.
Patio and outdoor furniture can be cleaned with or without detergent.
Freshwater should be used to pre-rinse the furniture and surrounding environment. If you’re using an all-purpose cleaner, place the detergent suction tube directly into the cleaning solution. And apply it to the surface at low pressure to prevent streaking. Allow 1-3 minutes for the all-purpose cleaner to sit on the surface. Allowing the detergent to dry on the surface is not recommended. Apply high pressure to the cleaning surface sweepingly. And maintaining the spray nozzle roughly 75mm to 150mm away from the cleaning surface. Clean top – bottom and left to right for the best effects.
Recommendations
If the paint on painted surfaces is peeling or chipping. Use particular caution when pressure washing the surface because the loose paint may be removed off the surface. Always begin with the largest degree nozzle possible to minimise paint damage.
Information relating to maintenance
Keep track of the regular servicing with the help of the Service Log. To ensure that your warranty remains valid. Be sure that the approved service agent has dated, signed, and stamped this log. Voiding the warranty is a possibility if you do not perform scheduled maintenance.
Filter for the fuel tank.
Inspect or replace the petrol tank filter. Every time you fill up the gasoline tank, inspect the fuel tank filter for any obstructions. If it is unclean, it should be replaced. Replace your fuel tank filter every 50 hours or three months, whichever comes first or is deemed essential. Remove the cap from the gasoline tank; Remove the fuel tank filter from the tank. If the fuel tank filter is clogged, replace it before using the pressure washer. Replace the cap on the gasoline tank. Incorporate the new gasoline tank filter into the top of the fuel tank, as shown.
Anode (spark plug)
The spark plug is recommended to be checked every 50 hours of operation or every 3 months. Replaced every 100 hours of operation or every 6 months. Whichever comes first or whenever it is determined to be required.
Unplug the spark plug lead; clean the spark plug base with a wire brush or nail file to remove the carbon deposits; check the spark plug gap with a feeler gauge. NGK BPR7ES or Torch F7RTC should be used in place of the original spark plug. The spacing between the two plugs should be 0.7mm to 0.8mm (0.028″ to 0.031″).